K3 - two radio support - Serial port and level converter support

Welcome Guest! To enable all features please Login or Register.

Notification

Error

LOGic Forum » Hardware Support » Serial port and level converter support » K3 - two radio support

K3 - two radio support

Options View

Previous Topic Next Topic

vk4iu		#1 Posted : Thursday, February 7, 2013 9:35:41 PM(UTC)
Rank: Advanced Member Groups: Moderator, Registered, Administrators Posts: 404 Location: Hodgleigh QLD Thanks: 6 times Was thanked: 77 time(s) in 68 post(s)		G'Day Dennis, I am moving to a "two radio" config for Logic for DXing. I run N1MM for contesting in an SO2R configuration using MicroHam MK2R+ and Station Masters. So in essence all the serial ports are virtual serial ports via the MicroHam Router (Eltima drivers) software. We are talking here about a different PC, a WinXP based system for contesting, as compared to the discussion elsewhere re Win 7 and Serial ports, Bluetooth etc - that PC is used for log analysis and reporting. I can run TRX Manager and configure two radios and both function correctly. If I configure Logic to use TRX Manager for both radios I get two copies of the ONE radio - see image below. The right radio should be on 15 meters. I guess the OLE interface to TRX Manager may not allow more than one radio. Yes? No? If I remove TRX Manager and configure Logic to control each radio directly, radio 1 starts cycling through a set of numbers one of which is the corrct frequency, while the second radio is correct. I can change modes and use the buttons on both radio toolbars, but radio 1 does not display the frequency. See a short video here If I configure OmniRig, both radios operate correctly. Where does the future lie here - with OmniRig? ... TRX Manager? ... or the Logic drivers? Peter VK4IU Peter VK4IU You can help by posting images of any errors and including your Logic version.
Back to top

User Profile View All Posts by User View Thanks
Sponsor
Note: We receive a commission from Amazon when you purchase via this link. It does not affect your cost. Thank you!
Back to top

WN4AZY		#2 Posted : Friday, February 8, 2013 9:15:08 AM(UTC)
Rank: Administration Groups: Administrators, Beta Testers Posts: 3,093 Location: Auburn, GA Thanks: 997 times Was thanked: 496 time(s) in 411 post(s)		Hi-- The TRX-Manager interface just looks like one radio to LOGic. It is my understanding that TRX-Manager actually supports only support one radio at a time. You could just switch between 4 radios. This is unlike LOGic, where all radios are active at once. That may have changed with TRX-Manager with an update -- I am not sure. What I recommend is interfacing one radio to TRX-Manager, and the other directly to LOGic. LOGic would still talk to TRX-Manager of course. From your video, I don't understand why the frequency is jumping around. What kind of radio is it? 73, DH
Back to top		WWW \| Edit by user

User Profile View All Posts by User View Thanks

vk4iu		#3 Posted : Friday, February 8, 2013 3:25:56 PM(UTC)
Rank: Advanced Member Groups: Moderator, Registered, Administrators Posts: 404 Location: Hodgleigh QLD Thanks: 6 times Was thanked: 77 time(s) in 68 post(s)		... both radios are Elecraft K3s. TRX Manager 4.7.2 has a concept of a "sub-reciever" - not a second receiver in the same radio, but a second radio on a second com port. It is only supported for some specific radios, of which the K3 is one. Peter VK4IU Peter VK4IU You can help by posting images of any errors and including your Logic version.
Back to top

User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (3)

LOGic Forum » Hardware Support » Serial port and level converter support » K3 - two radio support

Forum Jump

You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.